Showing posts with label not. Show all posts
Showing posts with label not. Show all posts
Tuesday, February 11, 2014
How to Make Standard Shams out of King Pillowcases How Not to Add Trim
Last week, I decided to attempt a quick update to the bedroom pillows with the addition of two shams. My quick attempt ended up taking a few days, but more on that later.
After searching locally for some simple and affordable white shams with no luck, I thought that it would be pretty easy to make standard shams out of king pillowcases.
It took me a little bit of time to figure it out, but once I did, it was really easy!
First I measured my pillow at ~ 16" x 26". The king pillowcase was 20" tall, so that would give me a 2" border which was perfect! I wanted the finished measurement (with a simple 2" border all around) to be 20x30.
From the open end, I ripped the seam out about 14" on both sides. From the closed end, I measured 31" for seam allowance (since I wanted the finished length to be 30").
I then cut the backside where I wanted the opening for the pillow to slip in (about 10" from the open end) I used the fabric I cut off to create the top part for the envelope. At this point, I checked to make sure there was enough overlap (about 3-5") and cut off any excess.
I turned the sham inside out and lay the smaller piece under neath the larger section. (Since it is inside out, make sure that the finished sides will be on the outside of the sham.)
I pinned and sewed the sides that the seam was taken out of, I left the the top flap un sewn and turned it right side out. Now I had the basic shape of a sham with the envelope closer on the backside. Almost done!
To match the other side (which isnt sewn), I closed the open end with heat n bond no sew adhesive. I folded the fabric under so it measured 30", put heat nbond inside and ironed.
Finally, I finished by sewing 2" in on all sides. I measured 2" from my needle and I put a piece of tape to keep my line straight. Once I got close to the edge I held a ruler up to measure 2" and then turned the sham to repeat.
I forgot to take a picture here, but about 30 minutes later it basically ended up looking like this :)
 |
| via |
Ok, now onto adding trim ... as you read in the title, this was not a DIY success. After looking at this pillow from Targets Modern Cottage collection, the basic premise was:
The ribbon basically sits on top of one another and each piece goes to the end with one side folded under at a 45. To make the ribbon line up at the inner corner and the outer edge it needs to be folded all the way to the edge.
Mistake # 1 since the cut edge of the ribbon needs to be folded all the way to the edge , it needs to be sealed to prevent fraying. The fraying wasnt too bad, but definitely to be washable, each piece would need to be cut and then sealed (maybe dip each end in a little craft glue?)
Pretty simple concept, but it ends up being a lot of detail work, like about 36 little exact folds that need to be ironed a few times.
Mistake # 2 If ironed too long, the heat n bond will show through the grosgrain ribbon. See it below?
err ... I could of covered it with a second accent ribbon on top, but decided that combined with the work involved in doing it on the other sham wasnt really worth it ...
Friday I talked about how I had a plan to get the corners flatter ... I was originally thinking of placing a thin piece of trim overtop the angle and and fold the edges under using heat n bond to secure it, but the fraying became an issue again. So I ended up applying a small amount of glue underneath just the ribbon and ironing. To get it as precise as possible, I used the tip of an xacto knife to avoid getting it everywhere. This worked really well and didnt take too long.
BUT ultimately I decided that the combination of not being able to wash them (because it would fray) and having to cover up the heat n bond wasnt worth it.
This could work, and I may try it again with these modifications:
1. After cutting the ribbon, seal with glue to prevent fraying.
2. Use a thicker cotton ribbon to prevent the heat n bond from showing through or sew the ribbon on. Sewing would be a good option since it is pretty hard to get the heat n bond everywhere.
So instead I ordered these shams from Crate and Barrel, Im still deciding if I want leave them alone or add a little something. Lets face it, I probably will :)
Lesson learned, always test a small area before doing the whole thing (like the heat n bond on the ribbon) and sometimes the time invested isnt worth it!
I may try it on a smaller throw pillow (now that I know what mistakes to avoid)
Better luck next time! :)
--
Update 2/24/13
See this post for how I successfully added trim!!
Sunday, January 26, 2014
Its Not Nice To Screw With Mother Nature
So I spent the summer tending my garden.
My old man was a gardener. When I was a kid, he bought a house that sat on a huge parcel of land and turned half of it into a vegetable garden. The property came with a bunch of apple, pear and cherry trees, as well as trestles full of grapes, raspberries and blueberries. He then added just about every type of vegetable that would grow in this climate.
I cant tell you how much I hated that garden. Every spring he would push me to till the damned thing, and every spring I would have to hear the, "When I was your age working the farms..." yarn that drove me nuts.
Fast-forward fifty years and there I was, willingly hanging on to a rotor tiller, whacking up the sod in my back yard, merrily turning it into a vegetable garden. I removed the sod, broke up the hard clay earth, mixed in sand and added sheep and cow shit to make it as comfy and cosy as I could for tomatoes, potatoes, peppers, corn and carrots, including a bit of a herb section to round it out. I weeded that bugger two or three times a week, spent a fortune watering it, spent hours trimmed things, staked others, and even made a couple of very cool looking tomato cages to make it all look more interesting and inviting. By the beginning of August we started to get a few juicy samplings as the plants started to come into maturity. This, of course, only served to make me work harder at it. I started pulling weeds more often, turning the soil between the rows bi-weekly and even started talking to them, although none of the rude buggers answered.
Come mid-August, I looked out the window overlooking the backyard and saw this...
I had noticed before I started that our property sat lower than our two neighbours, but didnt realize how low until we had a horrendous rain one Saturday afternoon. When the 5" of water finally disappeared, only two tomato plants and the impatiens that bordered it all survived.
I remember standing there, looking out that window at this lake that was once my garden patch, and hearing my old man laughing...
Peace,
Mitchell
Subscribe to:
Comments (Atom)